Description
About this item:
Auto Car Lift L 1100 220V 60HZ 1PH 3HP MOTOR features Symmetrical Arm Assembly with Straight Front / Rear 2 Stage reach from 30 1/4″ to 49 1/5″ and Equal length of front and rear arm design Drop-in type lifting pads and truck adapters are included.
Features:
Safety Mechanism:
- Double Point Safety Lock Release
- Automatic arm lock restraints
- Relief valve built in power pump to prevent overloading
- Door guards protection rubber
- Up-limit switch to protect cylinders working stroke used in safe length scope
- Heavy duty 5/16″ diameter cable and 4.56″ pulley reduce high stress on synchronization process and increase cable life
- Stiffened base plate 5/8″ thickness
- Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down
- Anchor bolts/mounting hardware included
Control System:
- Lifting operation by pressing “UP” button on motor
- Manual lowering operation by pressing lever
- Relief valve built in power pump to prevent overloading
- 1 sets truck adapters included
- Lifting Capacity: 10,000 lbs
- The overall Height 145-5/8″
- The overall Width 133-1/4″
- Column Width 10.62″
- Base Width 18.89″
- Column Thickness of Steel 3/16″
- Carriage Thickness of Steel 15/64″
- Arms Thickness of Steel 15/64″
- Front Arm 30.7″ to 48
- Rear Arm 30.7″ to 48″
- Min pad height: 3-7/8″
- Lift height max: 78-7/8″
- Drive-thru width clearance: 100″
- Time to full rise: 20-60 sec
- Shipping Weight: 1460 lbs
Site Selection:
Before installing your auto lift, check the following:
- Lift Location: Always use architect’s plans when available.
- Check layout dimension against floor plan requirements making sure adequate space is available.
- Your lift requires a 220v, 30amp, single phase, grounded electrical source. There should be room enough to operate the lift in a safe manner and without restrictions.
- Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.
- Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.
Floor Requirements:
- A level floor is suggested for proper installation and level lifting. Small differences in floor slopes may be compensated for by proper shimming. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.
- New concrete must be adequately cured for at least 30 days.
- DO NOT install auto lift on any asphalt surface or any surface other than concrete.
- DO NOT install auto lift on expansion seams or on cracked or defective concrete.
- DO NOT install auto lift on a second/elevated floor without first consulting building architect.
- DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.
Concrete Specifications:
All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift.
- 8,500 lbs – 10,000 lbs lifts: 4″ Minimum Thickness
- 11,000 lbs – 15,000 lbs lifts: 6″ Minimum Thickness
specifications:
- Condition: New
- Modified Item: No
- Custom Bundle: No
- Material: Metal
- Capacity: 10000lbs.
- Type: 2-Post Lift
- Features: Hydraulic
- Vehicle Type: Passenger Vehicle
- Brand: ,XK USA
- Non-Domestic Product: No
- Warranty: 1 Year
Randall D. –
The 220-volt power requirement is standard and should be easily accommodated in most garage or workshop settings.
Robert B. –
The 220-volt power requirement is standard and should be easily accommodated in most garage or workshop settings.
Walter K. –
A lift with a 10,000 lb capacity is likely to be versatile, accommodating different types and sizes of vehicles.
Zachary P. –
The absence of floor obstructions can be a significant advantage when working on the underside of vehicles.
Francis P. –
Users may appreciate the lift’s ability to handle substantial weight, making it suitable for a variety of vehicles.